Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;
I needed a garage door spring replaced that broke on a Saturday. I called around to several places and they were the most responsive and most up front with the estimate. Ryan came out with his trainee, replaced the spring and added a reinforcement to extend the life of the garage door panels in about 30 minutes. They inspected the motor and saw that it was in good shape. The service was excellent, the price was reasonable and they got it fixed in a reasonable time frame. Keep up the great work!

how to repair garage door spring


Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
If you have a single-car garage, an extension spring will do the job. If you’re looking for a smoother motion and an ability to lift heavier doors, you may be better off selecting the torsion spring option. And if you have a two-car garage, your door will likely be too heavy for an extension spring. In this case, the torsion spring is the better choice.

Garage doors use cable for several purposes. Many people might refer to this as ‘aircraft cable’ – it is a pliable twisted cable of a number of strands of galvanized wire. The primary use for this is a part called a ‘lift cable’. This cable is attached to the bottom corner of the door and then routed to the counterbalance spring as required by the type of counterbalance on your door. The secondary use for cable on many doors is a ‘retaining cable’. This cable is used on overhead type doors with extension or stretch type springs. The purpose of a retaining cable is to assist in preventing an extension spring from falling or flying in the garage in the event of breakage.
is to provide our customers with outstanding garage door repair services. We not only meet their expectations; we exceed them. We offer unmatched value, the best products in the industry, and services that simply can’t be beat. It’s no wonder why when the residents and business owners are in need of garage door repair services in Santa Rosa, we are the first company they call.
I immediately received a call back after leaving a message and got a same day appointment. Ryan, the technician, came out within the time frame quoted, was kind and super knowledgeable about garage doors. He quickly figured out that our keypad was not programming because of its location and the fact that it does not transmit through steel (which our garage door is partly made of). He installed an updated, more compatible keypad within minutes and like magic, we had a functioning keypad! He was kind enough to stay afterwards to explain the different functions on our garage door as well. On top of their stellar customer service, their prices are competitive and reasonable. The service fee was $89 and the keypad replacement was $75.

The following instructions can be followed by most do-it-yourselfers. You will need a second person to help you at the beginning of this tutorial to raise the door so that you can replace your torsion springs. These instructions are for replacing two springs on a self-storage roll-up door, also known as a mini-warehouse curtain door, that have the typical self-storage style loops on each end of the springs.

how to buy garage door torsion springs


It’s difficult to say how often the springs will need to be replaced since it’s different for everyone. It depends on how often you use your garage door, how cold and long your winters are, how well you maintain your springs and many other factors. The best rule of the thumb is to check your springs regularly for signs of wear and damage and to replace them when they begin to appear tired.
11/26/2018 Hi Christopher G., glad we we where able to provide you with great service, a quality job and for… Hi Christopher G., glad we we where able to provide you with great service, a quality job and for leaving us your feedback on the experience with our company. It's a great way of letting us know how we are doing and what areas are our strengths what areas we can improve from. Feel free to contact us for any future garage door servicing needs Read more

how to garage door repair


A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
First, with all the frauds and impersonate these day, I really appreciate it when Precision let me know who will be coming out and at what time? Tom was our Technician, he called ahead to let us know exactly when he would arrive and was on very prompt. Tom was very knowledge and professional, he represents his company very well and because of employee like him, I would definite recommend Precision to my family and friends. Thanks for being there when we needed you the most. Phu Le

up and over garage door repair kits


Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring.
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers. It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.

how to repair dent in garage door


Traditional One Panel: These doors consist of one large panel which tilts to open by employing a spring mechanism to swing upward. The wood version is popular in the South and Southeastern US, where a milder climate keeps the wood from rapidly deteriorating. Traditional garage door designs include Cape, Colonial, Ranch, Tudor and Craftsman. The disadvantage is these doors require a lot of clearance to operate correctly. Sometimes repairs can be difficult because of the heaviness of the door or its inaccessibility. Average cost to repair tilt-up doors is $172.
"I wanted to thank you for the overall great customer service Garage Door Nation recently provided me regarding a broken torsion spring on my 7'x16 garage door. Having heard the horror stories associated with DIY torsion spring replacements, I was concerned about my ability to tackle my garage door repair on my own. However, the expert videos on how to properly measure and order parts as well as the "how to" on the actual replacement made the project simple and straight forward. Additionally, I received my parts in three business days which allowed me to complete the repair ahead of schedule." 
×