Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.

how much garage door spring replacement


We believe we should treasure our natural resources, and our business practices reflect this ideal. All our service vehicles are flex-fuel efficient hybrids. When we have to throw away old parts, we recycle as many parts as possible. We clean up our trash after we complete a project. Our dispatch center is conscious about our carbon footprint and we use GPS technology and strategic planning to reduce our miles on the road.
Of course my garage door cables decided to snap at 5 PM on a Friday, leaving my garage door partially open. I searched yelp and started making calls and leaving voicemails and i figured i was out of luck. Daniel called me back and I told him what happened. Long story short, he showed up in an hour and fixed the cables and even tuned up my garage door. Not only is my garage door fixed, it's a whole lot less noisy and opens and closes smooth unlike before. Daniel was extremely friendly and he came last minute which saved my weekend. I highly recommend Molina garage door services and will be using them from now on.

how much does a garage door repairman cost


In each of our branches, we have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
Garage doors use cable for several purposes. Many people might refer to this as ‘aircraft cable’ – it is a pliable twisted cable of a number of strands of galvanized wire. The primary use for this is a part called a ‘lift cable’. This cable is attached to the bottom corner of the door and then routed to the counterbalance spring as required by the type of counterbalance on your door. The secondary use for cable on many doors is a ‘retaining cable’. This cable is used on overhead type doors with extension or stretch type springs. The purpose of a retaining cable is to assist in preventing an extension spring from falling or flying in the garage in the event of breakage.

Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.


If you want to take care of your garage door and do a little preventative maintenance on your garage door cables, you should have a working knowledge of what these components look like. Garage door cables are determined on two things, the weight of the door and how long the cable should be.  The heavier your garage door, like one made of wood, the thicker the cable you need.  Heavier garage doors obviously need stronger springs, which in turn require a thicker cable. The length of the garage door cable is determined by the kind of spring system you have for your garage door. Since the torsion spring system is only one or two springs at the top of the garage door, this type of spring takes a shorter cable.  Extension spring systems require a much longer cable, one that runs from the bottom of the garage door all the way up to the top on both sides.  Both cable types wrap around a drum at the top on each side as the garage door opens.
Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break.
The Torquemaster system has a lock built into each side on a double car door that will activate when a spring breaks causing the door to lock in the up position. It is very simple to deactivate this lock and get your door closed. But, you can guarantee you have a broken spring inside the Torquemaster tube on the side where the lock activated. You will need the spring inside replaced or have it converted over to a standard torsion spring set up, which is what we recommend and a service we perform quite frequently. A standard torsion spring will last 3 times longer than the small spring inside the Torquemaster tube.
Inspect your garage door cables often for fraying or kinks. Don’t forget to inspect the pulleys as well, as they can get worn out. If you find an area that is frayed, follow the cable’s path to see what could be causing the damage. There might be something sticking out that is damaging the cable, and you can remove the protrusion before it causes further damage. Keeping your cables clean is important to their health, as well. Remove any debris and keep your cables free of lubricants since they can attract dirt and grime, which can eventually cause your cables to stop working properly.

should you tip garage door repairman


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.

how to garage door installation instructions


If the door has come off its tracks in either the open or closed position, leave it in place. Attempting to close or open the door could result in the cables and springs also breaking. If the door is just being noisy, you need to have the rollers replaced and the tracks cleaned. Often, stuck rollers are due to insufficient lubrication and excess humidity.

how garage door repair


Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.

sears garage door repair service


Thank you for visiting Precision Garage Door Service of Seattle. We specialize in the repair of residential garage doors, openers, sales, service, & installation. Where ever you live along the Wasatch front, You have my personal guarantee that your experience with us will be professionally handled from start to finish. Your service will be provided by qualified & certified technicians that have completed the most extensive & rigorous training in the industry. We are proud of our environmentally sensitive business practices. Please give us a call to discuss your specific needs. We look forward to serving you.
×