If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.

should i repair or replace garage door opener


Thank you so much for being available and sending Ryan out to fix our garage. The door wasn't closing and finally I noticed 2 rollers off the track. Afraid the door would fall and also afraid to leave it open overnight I searched for 24 hour service. 30 minutes later Ryan arrived and fixed the door, lubricated the track and hinges and tightened everything up. I definitely feel safer knowing the door is in place. He also helped me program my homelink and taught us safety features we didn't know about! Thanks again for coming out on short notice.
The torsion springs on steel rolling doors work the same way as other torsion springs in the garage door industry. When the door is closed, the spring is wound. The spring is secured to a spring anchor bracket on one end and to the shaft on the other. When the steel rolling door opens, the spring in the barrel supports most of the door weight. The remainder of this weight is lifted by the chain hoist or the operator.

how to garage door seal


As a local, family-owned garage door service company at first we were focusing on providing garage door repair and garage door installation services mostly across Naperville, IL. However, it did not take a long time for the good word spread about our high-quality garage door service work and we started getting phone calls from all troubled homeowners looking for services. Today we are happy to offer our garage door services to the majority of the Northern Suburbs of Chicago.
I called Molina garage door service in the late afternoon regarding a door that was off the rails. Within 2 hours Daniel showed up to the property and had everything fixed in a short period of time. Although My only interactions with Daniel were via the phone, he was very professional and explained everything well. Everything was done for a fair price. Will highly recommend.

jerry garage door repair


Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;

united garage door repair


Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
This is the #1 reason why garage door springs fail or break! The average, properly installed torsion springs will last for approximately 10,000 cycles. A cycle is when the garage door goes up and then goes back down. Even if you were to only leave and come back once throughout the entire day, that still equates to two cycles per day or 730 in a year. That being said a garage door spring would only last for a little over 13 ½ years. However, most people open and close the door many times throughout the day, running many cycles, shortening that life span to far less than 13 ½ years. It is even possible to go through 10,000 cycles in about a year!

can you repair a bent garage door


Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.

home advisor garage door repair


I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.

A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]


Garage door spring snapped.  Called 4 companies for best price, best springs and longest warranties on parts and labor.  Search no further, Rockstar Garage had it all.  Manager, Louise, gave me a incredible deal and had service tech, Willie, out to my home same day, within 2 hrs!!  It was pouring rain too!  Willie went above and beyond to tune up my door, lube it and showed me some tricks to save more $$ in the future.  Just a class act all the way around!
×